Quick Reference Guide
Firmware Revision 3.51.00.20
The Quick Reference Guide provides a quick overview of your spa’s main functions and the operations accessible with your digital control pad.
Starting Pump 1:
Press Pump 1 button to turn Pump 1 on at low speed. Press a second time to turn Pump 1 to high unless it has been manually deactivated. The Pump 1 indicator lights up when Pump 1 is on speed. It flashes when Pump 1 is on at low speed.
Starting Pump 2:
Press Pump 2 button to turn pump 2 on. A second tome turns Pump 2 off. A built-in timer automatically turns Pump 2 off after 20 minutes, unless it has been manually deactivated.
The Pump 2 indicator lights up when Pump 2 is on at high speed.
Press Pump 3 button to turn Pump 3 on. Press a second time to turn Pump 3 off. A built-in timer automatically turns Pump 3 off after 20 minutes, unless it has been manually deactivated.
Starting Pump 4 button to turn Pump 4 on. Press a second time to turn Pump 4 off. A built-in timer automatically turns Pump 4 off after 20 minutes, unless it has been manually deactivated.
Starting Pump 5 button to turn Pump 4 on. Press a second time to turn Pump 5 off. A built-in timer automatically turns Pump 5 off after 20 minutes, unless it has been manually deactivated.
Starting the blower:
Press the Blower button once to turn on the Therapy Air (TA) blower. A second time turns the TA Blower off.
Setting water temperature:
Use UP or DOWN arrow button to regulate water temperature. The temperature setting will be displayed for 5 seconds to confirm your new selection. Water temperature can be adjusted by 1° increments from 59 to 104°F (15 to 40°C) The temperature symbol indicates the desired temperature, NOT the current water temperature.
Automatic water heater start:
When water temperature is 1°F (0.5°C) lower than the set Point, the heater will automatically turn on & heat until the water temperature reaches 1°F (0.5C) above the set point.
The heater indicator lights up when the heater is on.
Spa Boy® Boost (if equipped)
Press and hold the Pump 2 Key for 10 seconds to initiate Spa Boy® boost which runs the Spa Boy® electrode for 30 minutes regardless of the ORP setting. When activated “Sbb” will be displayed.
Push and hold the blower key for 20 seconds to invert the display.
Press hold the light button for 5 seconds to toggle between °F and °C
Turning the light on:
If your Spa is equipped with an original lighting package you can toggle through the the color options by pressing the light button ON/OFF/ON.
Press Light button to turn light on. Press a second time to turn light off. A built-in timer automatically turns it off after 2 hours, unless it has been manually deactivated.
The Light indicator is displayed when the light is on.
The Waterfall will be operated by turning Pump 1 on and adjusting a small bear paw control nearest to the waterspouts to vary the amount of flow. This can vary in location by the model series.
Press and hold Pump 3 Bu tton for 5 seconds to enter standby mode. The “stay” message is displayed and heating & filtering will be turned down while the heater is on, Pump 1 will run for an additional 3 minutes.
There are two modes you can choose from: Full or partial lock. Full lock means that all keypad functions are locked. Partial lock means that only the basic functions will remain accessible (pump, blower, light).
Locking your digital control pad:
Press and hold PUMP 1 for 5 seconds. The display will show “LocP” with “P” representing partial lock. Release the button and the keypad will be in Partial lock mode.
Keep button pressed down for 5 more seconds if you want to be in Full lock mode. The “LocF” message will then be displayed.
When control pad is locked, all automatic functions will run as usual. If a button is pressed down, a “LockP” or “LockF” message will be displayed for 1 second. To unlock the keypad, simply press and hold Pump 1 button again for 5 seconds.
Press and hold Pump 2 button for 5 seconds to enable Boost mode. In this mode, Pump 1 high speed and the ozonator will run for 45 minutes. When enabled, “boo” message is displayed. This mode os used to speed up filtration after intensive use of the spa or to help mix chemicals just added to the spa. Pressing and button will exit boost mode.
The fogger waterfall is controlled by pressing and holding the “light” button for 2 seconds. This will activate the system. Pressing the “light” button once will turn the fogger/waterfall off. The system will stay active for 2 hours unless it has been manually turned off using the “light” button.
It is advisable on first start up or restart that water is put into the opening of the fogger/waterfall to fill up the area to prevent premature damage to the fogger units.